Tủ môi trường nhiệt độ, độ ẩm 300 lít
Tủ môi trường nhiệt độ, độ ẩm 300 lít

Tủ môi trường nhiệt độ, độ ẩm 300 lít

Giá: Liên hệ

Model: TH-ICH-300 Nhà sản xuất: Jeiotech – Hàn Quốc Xuất xứ: Hàn Quốc   Yêu cầu báo giá Giá: Liên hệ Danh mục:

Hỗ Trợ Khách Hàng

Tổng đài hỗ Trợ Khách Hàng : 1900 066 870

HCM: N36 - Đường 11 - Tân Thới Nhất 17, khu 38 Ha, P. Tân Thới Nhất, Q. 12. TP. HCM

HN: P.502 - 12 Trần Quốc Vượng - P. Dịch Vọng Hậu - Q. Cầu Giấy - Hà Nội

Hotline: 0948870870 (Mr. Long) | Tel: 028.66870870

Mail: long.nguyen@technovn.net

  • Mô tả sản phẩm
  • Tài liệu
  • Điều kiện thương mại

Tính năng kỹ thuật:

Tính năng an toàn:

  • Completed photostability test alarm.
  • Built in door lock.
  • Automatic shut off after overheat alarm.
  • Low and empty water level alarm.
  • Power supply leakage breaker.
  • Over current protection.
  • Overheat protection.
  • Door open alarm.

Tính năng vận hành:

  • Microprocess PID control / Auto-tuning / Calibration.
  • User friendly LCD controller.
    • Set value and present value are clearly visible together on display.
    • Operating progression visible in graph mode allow for direct data interpretation.
    • Temperature and other operating parameters recorded with use of an optional recorder. (optional)
  • Sufficient programmable control support.

Description

TH-ICH

Programmable Pattern Capacity

10

Pattern Repeat Time

999

Max. Segments per a Pattern

100

Available Max. Segments*

10

Programmable Process Time per a Segment

0 to 99 hr 59 min

* Even though the max. segments per a pattern are 100, available total segments are up to 300 not 3000,
so you need to arrange the number of segment an patterns properly

  • Computer interface:
    • RS-485 communication port enables connection of up to maximum 9 units. Simultaneous monitoring and operating of multiple units is an available feature. (optional)
    • Program patterns are simple to set with the use of our software.
    • Storage of program information, backup of value settings / recovery, and temperature values.
    • RS-232C port as standard offer.

Tính năng cấu trúc:

  • Two different sized models available to suit any users’ needs
  • Rapid humidity control is achieved by adapting the humidification tank interior to the chamber.
  • Corrosion resistance stainless steel chamber and electric polished humidification tank.
  • Air-tight door closure with perfect sealed packing.
    • Heat-resistant silicone packing completely blocks high heat leakage from the inner chamber.
  • Cable port for external probes or wires.
    • 50mm diameter cable port comes standard on the left side of the unit. Additional 50mm or 80mm diameter cable ports can be custom ordered. (optional)
  • Inner glass door with entry ports for handling samples without affecting inner chamber temperature and humidity. (optional)
  • Casters for easy mobility during installation or relocation.

Features for Stability Test ICH Guideline Q1A (R2):

  • Operating progression visible through graph mode for better data analyzation.
  • Cyclic defrost system, designed to work excellently for the long period stability test operation.

(* Temperature and humidity changes may occur during automatic defrost.)

  • Maintenance of water supply are easily performed with a front water tank.
  • Water level check indicated by water level bar in the tank.
    • Water supply during operation is also available for long term test purposes.
  • Direct water system provides user great convenience when performing long-term test.(optional)

Features for Photostability Test ICH GuidelineQ1B (Option 2):

  • Built in UV and fluorescent lamps for uniformed luminescence.
  • Equipped with movable UV and VIS sensors.
  • Independent lamp controller.
    • An indicator for Total usage time of UV and fluorescent lamps.
  • Convenient set function of cumulative dosage and lamp Off.

Thông số kỹ thuật

Thông số kỹ thuật:

Model

TH-ICH-300

TH-ICH-800

Chamber Volume (L / cu ft)

300 / 10.6

760 / 26.8

Controller

PID control (LCD Type)

Temperature 1)

Range

without Humidity (℃ /oF)

-5 to 85 / 23 to 185 without Light

0 to 85 / 32 to 185 with Light

with Humidity (℃ / oF)

+15 to 85 / 59 to185 with Light

Fluctuation 1) (±℃ / oF) at 40℃ / 60%RH

0.3 / 0.55

0.3 / 0.55

Variation 1) (±℃ / oF) at 40℃ / 60%RH

0.5 / 0.9

0.7 / 1.3

Humidity

Range (%RH)

FULL RANGE : 20 to 85
40 to 80 at 15℃ (59oF)
30 to 85 at 30℃ (86oF)
20 to 85 at 50℃ to 85℃ (122oF to 185oF)

Fluctuation 2) (±%RH) at 60%RH / 40℃

3

Variation 2) (±%RH) at 60%RH / 40℃

5

Light Source
(ICH Q1B option 2)

Cool White 3)

6,000 lux

6,500 lux

Ultraviolet-A 3)

4.5 W/㎡

5 W/㎡

Light Uniformity

VIS. : ±10% UVA : ±15%

VIS. : ±15% UVA : ±15%

Typical Time Required to Reach ICH Recommendation of 1.2 million lux-hr

≒ 200Hr

≒ 184Hr

Typical Time Required to Reach ICH Recommendation of 200 W-hr/m2

≒ 50Hr

≒ 40Hr

Time

Heating 4)

25min (20℃ → 85℃)

30min (20℃ → 85℃)

Cooling 4)

35min (20℃ → -5℃)

40min (20℃ → -5℃)

Refrigeration

System

Air - cooled

Refrigerant

R- 404A

Capacity (W)

250

470

Cooler

Copper plate fin cooler

Heater

Material

Ni-Cr Wire Heater / SUS Tube Heater

Drying Bulb (W)

1500

2300

Humidity Bulb (W)

1200

2000

Sensor

Temperature

Pt 100

Humidity

Electronic sensor (Free of drying a wet pack and good response time)

Air Flow

2 set of sirocco fan (2×60 W) : Vertical type

Material

Internal

SUS #304 (2B polish)

External

SUS #304 (Hairline finish) & Steel, 2t, Double painted & baked

Insulation

Polyurethane (70mm / 2.76")

Door

EPDM Sheet

Operating Temperature

18℃ to 30℃ / 64.4oF to 56oF, 85%RH (Non-corrosive and pure place)

Water Tank

Capacity (L / cu ft)

15 / 0.53

Water Quality

pH6.2 ~ 7.2, Electrical conductivity 20㎲ / cm to below

Interface Port

Basically RS-232C, [RS-485 : optional]

Cable Port

Basically one hole provided / Ø 50mm (2"),Optionally max. two holes available / Ø 50 or 80mm (2 or 3.2")

Quantity of Wire Shelves (included / max.)

2 / 8

2 / 17

Distance of between Shelves (mm / inch)

60 /2.4

Dimension
(W×D×H)

Internal (mm / inch)

750×650×650 / 29.5×25.6×25.6

750×880×1160 / 29.5×34.6×45.7

External (mm / inch)

1130×985×1520 / 44.5×38.8×59.8

1220×1215×1965 / 48×47.8×77.4

Net Weight (kg / lbs)

280±10 / 617±22

400±10 / 882±22

Electrical Requirements

AC230V, 1ph, 50Hz

14.7 A

23.5 A

Cat.No.

AAHC1002K

AAHC1012K

1) All specifications are under ambient temperature 20℃ (68oF), No load.
2) Technical data according to DIN 12880, IEC 60068.
3) The value is measured on the center of chamber at the point of vertical direction.
4) Up to 98% of the set value.

Cung cấp gồm / Phụ kiện

Cung cấp bao gồm:

  • Tủ môi trường nhiệt độ, độ ẩm 300 lít; Model: TH-ICH-300; Code: AAHC1002K
  • Phụ kiện tiêu chuẩn
  • Tài liệu hướng dẫn sử dụng tiếng Anh + tiếng Việt

ĐIỀU KIỆN THƯƠNG MẠI:

  1. Điều kiện chung:
  • Giá niêm yết đã tính các khoản thuế và chi phí như: thuế nhập khẩu, vận chuyển, bảo hành, giao hàng, lắp đặt và hướng dẫn sử dụng tại đơn vị sử dụng tại nội thành Tp. Hồ Chí Minh;
  • Giao hàng; lắp đặt và hướng dẫn sử dụng tại các tỉnh: thỏa thuận phí trong từng trường hợp cụ thể;
  1. Thời gian giao hàng: Tùy theo thời điểm đặt hàng - Ưu tiên đơn hàng đến trước:
  • Hàng có sẵn: giao hàng trong 01 - 05 ngày kể từ ngày đơn hàng có hiệu lực;
  • Hàng không có sẵn: sẽ trao đổi chính xác tại từng thời điểm đặt hàng sau khi kiểm tra và có thư xác nhận từ sản xuất hoặc từ đơn vị phân phối;
  1. Thời gian bảo hành:
  • Thiết bị mới 100% được bảo hành 12 tháng theo tiêu chuẩn của nhà sản xuất đối với máy chính;
  • Điện cực máy để bàn + Cầm tay bảo hành 6 tháng
  • Điện cực bút đo bảo hành 3 tháng
  • Chế độ bảo hành không áp dụng đối với những lỗi do người sử dụng gây ra, phụ kiện, đồ thuỷ tinh, vật tư tiêu hao…
  • Ghi chú: Một số trường hợp có thời gian ngắn hoặc dài hơn 12 tháng - tùy chính sách bảo hành của Nhà sản xuất - công ty chúng tôi sẽ thông báo từng trường hợp cụ thể lúc nhận được yêu cầu;
  1. Địa điểm giao hàng:
  • Miễn phí trong nội thành Tp. Hồ Chí Minh;
  • Thỏa thuận trong từng trường hợp cụ thể nếu giao hàng đến các tỉnh;
  1. Thanh toán:
  • Đối với các giao dịch có hóa đơn VAT dưới 20.000.000 VNĐ: chấp nhận thỏa thuận giao dịch bằng tiền mặt thanh toán hoặc chuyển khoản qua tài khoản công ty hoặc tài khoản cá nhân do công ty chỉ định
  • Đối với các giao dịch có hóa đơn VAT bằng hoặc trên 20.000.000 VNĐ: bắt buộc giao dịch qua chuyển khoản vào tài khoản công ty;
  • Nếu giao dịch là đồng ngoại tệ thì thanh toán theo tỷ giá bán ra của Ngân hàng Ngoại Thương tại từng thời điểm thanh toán;
  • Số lần thanh toán và tỷ lệ thanh toán: thỏa thuận theo từng đơn hàng cụ thể;
  • Đơn vị thụ hưởng:

Công ty TNHH Kỹ Thuật TECHNO

Số tài khoản VNĐ: 04101010022719

Tại: Ngân hàng Maritime Bank, Chi nhánh Sài Gòn      

 

Thông tin liên hệ trực tiếp:

Mr. Nguyễn Hoàng Long - Director

Tel:     0866 870 870   -   Fax: 0862 557 416

Mobil: 0948 870 870

Mail:   long.nguyen@technoshop.com.vn

            sales@technoshop.com.vn

CÔNG TY TNHH KỸ THUẬT TECHNO

GIÁM ĐỐC

 

 

 

 

NGUYỄN HOÀNG LONG

 

 

   Đối tác - Khách hàng

   Dịch vụ của chúng tôi

TƯ VẤN BÁN HÀNG NHANH

0948 870 871 - 0946 224 336

VẬN CHUYỂN TOÀN QUỐC

An toàn - nhanh chóng

THANH TOÁN LINH HOẠT

Hỗ trợ khách hàng tốt nhất

BẢO HÀNH CHÍNH HÃNG

Cam kết chính hãng

   Tin tức chuyên ngành xem tất cả   

zalo chat
Mr. Long 0948 870 871